French   Italiano   Spanish   German   Portuguese   Korean   Japanese 中国
Home Log In
OBD2CODING
Automotive Diagnostic Supplier
  • MB Star Diagnostic tool
  • Auto Diagnostic Tool+
    • Car diagnostic tool
    • truck diagnostic tool
    • car diagnostic interface
    • Car Repair tool
    • OBDII Cable and Connector
    • car diagnostic software
  • obd2 Coding Readers
  • Original Brand Tool
  • Test Sockets and Programmers+
    • Programmer Socket Adapter
    • Device programmer+
      • IPhone hard-disk test fixture
      • Universal Programmer
  • Auto Locksmith Tools+
    • Car Key Programmer
    • Car Locksmith Tool
    • car transponder chip
    • key remote controls
  • ECU Chip tuning Programmer+
    • Odometer Correction Tool
    • Ecu Chip Tuning
    • Auto Ecu Programmer
  • Soldering Tools
  • Vehicle Immo Emulator+
    • IMMO Sensor Emulator
    • SRS Emulator
    • Service Airbag Reset
  • Car Accessory Tool+
    • Hot Car Accessories
    • car pixel repair
    • Universal IC Chip
  • transponder key...,
  • upa usb programmer,
  • VAG Cable,
  • VAG COM,
  • My Cart
    0
    Your cart is empty.
    Wish List
    0
    CATEGORIES
    MB Star Diagnostic tool
    Auto Diagnostic Tool
    • Car diagnostic tool
    • truck diagnostic tool
    • car diagnostic interface
    • Car Repair tool
    • OBDII Cable and Connector
    • car diagnostic software
      Launch OBD Cable for X431 V /PRO /Easydiag 3.0/2.0/Mdiag/Golo 3 OBD2 Extended Connector 16Pin
      Launch OBD Cable for X431 V /PRO /Easydiag 3.0/2.0/Mdiag/Golo 3 OBD2 Extended...
      VAG COM VCDS 18.2.1 RUS full active cable VAGCOM 18.2 Russian VCDS 17.8 русский update online interface
      VAG COM VCDS 18.2.1 RUS full active cable VAGCOM 18.2 Russian VCDS 17.8...
      VAG COM VCDS 18.9.0 EST full active cable VAGCOM 18.2 Spanish VCDS 18.9 Español update online interface
      VAG COM VCDS 18.9.0 EST full active cable VAGCOM 18.2 Spanish VCDS 18.9...
      A1 OBD2 Adapter Cable for CARPROG V4.7/V8.21/V9.31/V10.5
      A1 OBD2 Adapter Cable for CARPROG V4.7/V8.21/V9.31/V10.5
    obd2 Coding Readers
    Original Brand Tool
    Test Sockets and Programmers
    • Programmer Socket Adapter
    • Device programmer
      • IPhone hard-disk test fixture
      • Universal Programmer
      BDM Probe Adapters KTAG KESS KTM Dimsport BDM Full Set 22pcs (Denso, Marelli, Bosch, Siemens)
      BDM Probe Adapters KTAG KESS KTM Dimsport BDM Full Set 22pcs (Denso, Marelli,...
      NAND BGA64 Test Socket adapter for PROMAN TL86_PLUS NAND Programmer
      NAND BGA64 Test Socket adapter for PROMAN TL86_PLUS NAND Programmer
      CNV ssop16 to dip16 socket 16 pin ic socket tssop16 ic test socket
      CNV ssop16 to dip16 socket 16 pin ic socket tssop16 ic test socket
      CNV msop8 8 pin adapter 0.65mm ic socket ssop8 8 pin ic socket
      CNV msop8 8 pin adapter 0.65mm ic socket ssop8 8 pin ic socket
    Auto Locksmith Tools
    • Car Key Programmer
    • Car Locksmith Tool
    • car transponder chip
    • key remote controls
      SBB Pro2 V48.88 Key Programmer SBB 48.88 update SBB V46.02
      SBB Pro2 V48.88 Key Programmer SBB 48.88 update SBB V46.02
      Mart Tool Key Programmer for Jaguar Land Rover KVM FK72 HPLA for All Keys Lost till 2018
      Mart Tool Key Programmer for Jaguar Land Rover KVM FK72 HPLA for All Keys Lost...
      OBDSTAR H105 Hyundai Kia Pin Code Reader Key Programmer Device H105 Mileage Programmer
      OBDSTAR H105 Hyundai Kia Pin Code Reader Key Programmer Device H105 Mileage...
      Auto Computer control module IC TA8260AH ECU board chip
      Auto Computer control module IC TA8260AH ECU board chip
    ECU Chip tuning Programmer
    • Odometer Correction Tool
    • Ecu Chip Tuning
    • Auto Ecu Programmer
      MT008 VAG NEW MQB MILEAGE CORRECTION TOOL MT008 Odometer Master
      MT008 VAG NEW MQB MILEAGE CORRECTION TOOL MT008 Odometer Master
      MC68HC11 Motorola 711 Programmer MC68HC11 711 Programming tool
      MC68HC11 Motorola 711 Programmer MC68HC11 711 Programming tool
      EURO K-TAG V7.020 KTAG 7.020 online Master Full Protocols with Unlimited Token
      EURO K-TAG V7.020 KTAG 7.020 online Master Full Protocols with Unlimited Token
      XPROG M V5.72 ECU Programming Xprog M 5.72 Programmer Xprog V5.72 No USB Dongle
      XPROG M V5.72 ECU Programming Xprog M 5.72 Programmer Xprog V5.72 No USB Dongle
    Soldering Tools
    Vehicle Immo Emulator
    • IMMO Sensor Emulator
    • SRS Emulator
    • Service Airbag Reset
      TPMS-Sensor 433MHz/315MHZ Universal Sensor for Tire Pressure Sensor Replacement
      TPMS-Sensor 433MHz/315MHZ Universal Sensor for Tire Pressure Sensor Replacement
      Special BDM+4 Adapter for CG100 Airbag Restore Devices Renesas
      Special BDM+4 Adapter for CG100 Airbag Restore Devices Renesas
      Carprog Full Firmware with All 21 Adapters Plus New V54 FGTech Galletto 4
      Carprog Full Firmware with All 21 Adapters Plus New V54 FGTech Galletto 4
      Auto Immobilizer Emulator IMMO for Renault
      Auto Immobilizer Emulator IMMO for Renault
    Car Accessory Tool
    • Hot Car Accessories
    • car pixel repair
    • Universal IC Chip
      OBDII Protocol Detector & Break Out Box OBD2 connector link Box
      OBDII Protocol Detector & Break Out Box OBD2 connector link Box
      AUDI/VW/BENZ/BMW Automotive Programming Dedicated Power
      AUDI/VW/BENZ/BMW Automotive Programming Dedicated Power
      TK102 GPS GSM GPRS Tracker/ Vehicle TK102 GPS Tracking device
      TK102 GPS GSM GPRS Tracker/ Vehicle TK102 GPS Tracking device
      SAK-XC161CJ-16F40F SAK-XC161CJ TQFP-144 new original
      SAK-XC161CJ-16F40F SAK-XC161CJ TQFP-144 new original
    Brands
    • AUTEL
    • GJ
    • Hantek
    • LAUNCH X431
    • LISHI
    • Made in China
    • QUICK
    • Runfei
    • SAIKE
    • XELTEK
    • xhorse
  • Home
  • Specials
  • Featured Products
  • All products
  • Reviews
  • Contacts
    • Home
    • Test Sockets and Programmers
    • Programmer Socket Adapter
    • BDM Probe Adapters KTAG KESS KTM Dimsport BDM Full Set 22pcs (Denso, Marelli, Bosch, Siemens)

    Press Esc key to close this popup
  • BDM Probe Adapters KTAG KESS KTM Dimsport BDM Full Set 22pcs (Denso, Marelli, Bosch, Siemens)

    • Model: ST230
    • Shipping Weight: 0.68kg
    • Units in Stock: 1000

    Price:   $165.90  $89.9946% off

    (0 reviews)
    -+
    (complete orders today,deliverd around 26/02/2019)
    Free Shipping
    Wholesale price contact us!
    • Shipping time
      Fast shipping 5-7 days.Normal shipping 10-45 days.
    • means of transportation
      EMS,TNT,UPS,DHL,FEDX,HK POST
    • Payment
      Paypal,Western Union, MoneyGram
    • Email us
      obd2coding@hotmail.com
    Download this product pictures
  • bdm100 (1)
  • benz key programmer (7)
  • benz nec programmer (2)
  • bmw inpa (2)
  • Can clip (2)
  • can filter (5)
  • car key programmer (3)
  • carprog (3)
  • ck-100 (4)
  • Dealer Level Diagnostic Tools (3)
  • delphi ds150 (1)
  • digiprog3 (5)
    • Details
    • Reviews
    • Tags
    • FAQ

    BDM Probe Adapters Full 22pcs Set for KESS KTAG KTM Dimsport . obd2coding Kess K-tag KTM Trasdata BDM Probe Set with 22pcs adapters For Denso, Marelli, Bosch, Siemens.  KESS KTAG KTM Dimsport BDM Probe a full set of BDM adapters for K-TAG/KESS /KTM/Trasdata chip tuning tool.



    KTAG KESS KTM Dimsport BDM probe adapters full set 22pcs for Denso, Marelli, Bosch, Siemens


    BDM Frame adapters full 22 sets Features:


    Adapter width: ~60mm width for original BDM Probe, not for low quality plastic with 40mm width.
    Adapter thickness: 2mm
    Adapter colour: Green
    A full set comes with 22 BDM adapters.


    FULL SET OF KTAG KESS KTM ADAPTERS FOR POSITIONING FRAME  
    INCLUDES FOLLOWING ITEMS:
     

    1 14AM00T01M Bosch
    2 14AM00T02M Delphi DCM
    3 14AM00T03M Bootloader ST10xx
    4 14P600KT04 Infineon Tricore EDC/MED17
    5 14AM00T05M Marelli MPC55xx JTAG
    6 14AM00T06M Delphi MPC55xx JTAG
    7 14AM00T07M Denso CN1 Boot
    8 14AM00T08M Denso CN2 Boot
    9 14AM00T09M Denso CN3 Boot
    10 14AM00T10M Denso CN1 AUD
    11 14AM00T11M Denso CN2 AUD
    12 14AM00T00M Delphi DCI
    13 14AM00TBAS Base Adapter 1.27
    14 14AM00T14M NexusEFI T6 Lotus
    15 14AM00TB02 Magneti Marelli BDM insert
    16 14AM00TB01 Siemens BDM insert
    17 14AM00TB03 EDC7 BDM insert
    18 14AM00T18M Magneti Marelli MPC/SPC56xx
    19 14AM00T13M Nexus MPC5xx TRW ECU
    20 VAG 1.6tdi - Siemens-Continental PCR2.1
    21 14AM00T15M Toyota NEC76F-20
    22 14AM00T16M Toyota NEC76F-26

    Package Show:

    bdm-adapter-full-set obd2coding.jpg

     

    How to use BDM probe adapter with KTAG/KESS/KTM100/Dimsport?

     

        Open the ECU

        at least one part of the casing (top or bottom) needs to be removed
        refer to other sources (Internet) to get information on which part needs removing on your

    ECU

     

        Locate the ECU BDM connector

        usually a set of 10 – 12 pads in two rows (depending on the ECU)
        pads may be 2.54 mm or 1.27 mm apart (depending on the ECU)
        rows may be 2.54 mm or 5.08 mm apart (depending on the ECU)
        if the ECU BDM connector can not be located, chances are that the BDM pads are scattered

    all over the ECU PCB in which case you can not use the adapter directly – nevertheless it is

    possible to manually route the adapter BDM signals to the ECU BDM pads (only for

    advanced users)

     

        Locate the ECU BDM pin 1 position

        pin 1 is usually not clearly marked on the ECU BDM pin out
        on an ECU with the standard Motorola BDM pin out pins 3 and 5 are connected to ground –

    this can be checked either visually or using a multimeter tool

        refer to other sources (Internet) to get more information on the pin 1 position for your ECU

     

        Place the desired adapter in the frame saddle

        make sure the pogo pins are facing out
        lift the saddle so that the ECU can be slided under the frame adapter saddle

     

        Place the ECU on the frame

        inspect the adapter for pogo pin 1 location which is clearly marked
        rotate the ECU on the frame so that the adapter pogo pin 1 and ECU BDM pin 1 match
        make sure ECU is firmly sitting on the frame
        double check the ECU position

     

        Connect the multiplexer board and adapter

        at this point multiplexer board should be connected to the adapter via MUX connector
        this will allow LEDs on the adapter to illuminate the area of interest (where the pogo pins

    need to touch the ECU BDM pads)

        do not connect the tool yet

     

        Connect the external power (+12 V) to the multiplexer

        multiplexer external power is used to power the LEDs on the adapter allowing easier

    positioning of the adapter pogo pins on the ECU BDM pads

        red LED on multiplexer board will light up when external power (+12 V) is present
        at this point the white LEDs on the adapter should also light up
        do not connect the tool yet

     

        Fine tune the ECU position

        lower the frame adapter saddle to almost touch the ECU BDM pads
        each adapter pogo pin needs to sit on a separate ECU BDM pad
        if pogo pins do not sit on the pads you may be using the wrong adapter – do not use the

    adapter in this case!

     

        Lower the frame adapter saddle

        each adapter pogo pin should sit on one ECU BDM pad
        minimum down force should be applied when making the interconnection between the

    adapter and ECU

     

        Double check the adapter pogo pin and ECU BDM pad interconnection

        in order not to damage the ECU and/or tool make sure that the steps above have been

    performed correctly

     

        Connect the tool to the multiplexer board

        only connect one tool at any given moment to the multiplexer
        make sure to use the correct 10-pin IDC connector (FGTECH, XPROG, BDM100&KTAG)

    for interfacing the tool used:

    ○ use provided 10-pin to 10-pin cable with FGTECH or BDM100 tools

    ○ use provided 10-pin to 16-pin cable with XPROG tool

    ○ use manufacturer 10-pin to 25-pin cable with KTAG tool

        do not connect the tool to the 10-pin IDC connector labeled MUX
        do not power up the tool yet

     

        For Bosch adapter only

        Bosch ECUs need to have ECU power supplied on the pogo pins (2 and 9)
        some tools provide dedicated ECU power (BDM100, KTAG) while others do not

    (XPROG, FGTECH)

        Bosch adapter can be used in both cases, providing that the jumper is properly placed on

    the 3-pin header (found on the adapter)

        place the jumper on the adapter on the 3-pin header to the correct position:

    ○ place jumper over left and central pins when using XPROG and FGTECH tools – this will use +12 V power delivered from the multiplexer board (external power) for powering the ECU

    ○ place jumper over right and central pins when using BDM100 or KTAG tools – this will use

    +12 V power delivered by the tool for powering the ECU

     

        For Siemens, Delphi and Marelli adapters only

        Siemens, Delphi and Marelli do not provide ECU power on the pogo pins
        in order to power the ECU +12 V and ground signals needs to be connected to the ECU separately (usually over the ECU interfacing connector)
        in this case ECU power can be taken from multiplexer board connectors J2 (+12 V) and J3 (ground), otherwise provide the +12 V ECU power from additional source
        refer to other sources (Internet) to get more information on the location of the +12 V and

    ground pin location for your ECU

     

        Connect the tool to the PC (or power up the tool)

        perform software installation as described by the tool manufacturer if not done already
        at this point the multiplexer, adapter and the ECU should be properly interconnected with

    BDM signals and power lines

    ○ multiplexer red LED should be lit up

    ○ adapter white LEDs should be lit up

    ○ ECU power (+12 V) should be present

        connect the tool to the PC (usually done over USB or serial connection)

     

        Perform BDM operation(s)

        start up the software package to operate the tool
        perform desired BDM operation(s)Note: The user manual is used for reference; in fact, it depends. Try on your own risk.


    OBD2coding After-Sale Service:


    Technical Support: Free

     
    Whatsapp:+86-18566221426
    Live Support: Chat with us online
    Email: obd2coding@hotmail.com
    Yahoo: obd2coding@yahoo.com
    Skype: yinmilo

    If you have any problem, please do not hesitate to contact us.

     
    Wholesaler Discount: If you are wholesaler or reseller, pls send email to obd2coding@yahoo.com,  we will give you best discount for long-term cooperate.


    Payment Terms: We accept payment by paypal, western union, money gram and bank transfer.

     
    Shipment Note:

     
    1. All our free shipping items can track it online after delivery, you don't worry about your order status.
    2. Express Delivery we will send to you with DHL,EMS,UPS,FEDEX,TNT..., please give us a valid delivery phone number, and also a full and accurate shipping address.

     
    How to make order on OBD2coding.com?

    Notice: After you place order, pls reply confirm email send by obd2coding@yahoo.com asap for us to arrange ship for you, thanks


    Please tell us what you think and share your opinions with others. Be sure to focus your comments on the product.




    Add you Tags
    TAGS:

    Your page text goes here

    Similar Products more
    OEM Orange5 Professional Programmer full adapter without main unit orange 5 adapter
    OEM Orange5 Professional Programmer full adapter without main unit...
    $78.90
    eMMC169 eMMC153 Test Socket Adapter BGA169 BGA153 Clamshell
    eMMC169 eMMC153 Test Socket Adapter BGA169 BGA153 Clamshell
    $85.00
    Specialized BGA105 flash memory adapter for up818 up828
    Specialized BGA105 flash memory adapter for up818 up828
    $210.00
    UP-818 UP-828 BGA108 flash memory chip BGA108 socket adapter
    UP-818 UP-828 BGA108 flash memory chip BGA108 socket adapter
    $258.00
    SBGA165 ic socket adapter SBGA165 mobile flash memory chip adapter for up818 up828
    SBGA165 ic socket adapter SBGA165 mobile flash memory chip adapter...
    $413.00
    QFN20 TO DIP20 20 pin programmer adapter
    QFN20 TO DIP20 20 pin programmer adapter
    $69.00
    Quick Links
  • Home
  • Specials
  • Featured Products
  • All products
  • Reviews
  • Contacts
  • Customer Service
  • about us
  • Shipping
  • About Wholesale
  • Payment
  • News
  • Tags
  • My account
  • login
  • My Cart
  • Wish List
  • Site Map
  • My Account
  • Contacts
  • Follow us
  • Lorem Ipsum as their default model text, and a search for lorem ipsum will uncover many web sites still in their infancy.
  • Copyright © 2019 obd2coding.com obd2coding Wholesale Auto Diagnostic service Center
  • RSS Product Feed :: BDM Probe Adapters KTAG KESS KTM Dimsport BDM Full Set 22pcs (Denso, Marelli, Bosch, Siemens)